| Mercury: 135-300hp with 3 RAM Trim/Tilt
systems, (INCLUDES VERADO 4 CYLINDERS)
Honda:
75-250hp with 3 RAM Trim/Tilt
systems
Yamaha: 115hp-350hp with 3 RAM Trim/Tilt systems
Suzuki: DF90,DF140-DF300hp 4-Stroke with 3 RAM Trim/Tilt
systems
Johnson: 60hp-250hp 4-Stroke with 3 RAM Trim/Tilt
systems
Johnson/Evinrude V4:140hp
with 3 RAM Trim/Tilt systems
Johnson/Evinrude V6:
150hp-250hp with 3 RAM Trim/Tilt systems
Works on these models: Carb. EFI, Opti-Max, 2-Stroke, 4-Stroke, Hpdi, ETEC,Ficht and
Offshore, with 3 RAM Trim/Tilt Systems
Install on trim/tilt switch side, normally Starboard Side of Mercury/ Honda /Johnson 4-Stroke, Johnson/Evinrude Outboards.
Install on trim/tilt switch side, normally Port Side of Yamaha/Suzuki Outboards, F300-F350 V-8 models need 2 m-ywedge units, port
and starboard.
1. Trim outboard to up position.
2. Simply slide M-Y Wedge on Trim/Tilt switch side normally Port side (see
note) of Yamaha/Suzuki and normally Starboard side of Mercury/ Honda/ Johnson/
Evinrude over Trim/Tilt piston rod of Lower unit .
Note: (On Yamaha/Suzuki
the trim/tilt switch may be on the Starboard
side, if there is a grease zerk where the m-ywedge
meets the swivel bracket, the m-ywedge must go on the Port or Starboard
side depending on where the grease zerk is.)
3. M-Y Wedge will position and self-center,
slide completely down.
4. Trim outboard down until the rubber begins to compress.
5. To remove M-Y Wedge simply trim outboard to up position and remove.
6. Store M-Y Wedge in any boat compartment for convenience.
Note: We recommend that you rotate M-Y Wedge, 1/4 to 1/2 turn after each use. This
helps even the compression of the EPDM Rubber on the unit.
***
PRINTABLE VERSION ***
Click Here for a Printable Version
of the Yamaha/Suzuki Instructions
***
PRINTABLE VERSION ***
Click Here for a Printable Version
of the Mercury/Honda/Johnson/Evinrude Instructions |
Mercury Starboard Side - Installs on
Trim/Tilt Piston - Self Centers, Snug Down to Secure
Correct Trailering Height
No Need to Hold on to
Anything!!!
Yamaha Port Side -
Trim/Tilt Piston
Self Centers
Lower Until Starboard
Piston Retracks 1/4" to 1/2"
To Secure. Correct Height for Trailering.
|
| The Universal m-ywedge unit
works on the single ram power tilt system. Kicker
motors with power tilt systems.
Mercury; 125hp-40hp with single ram power tilt
systems.
Yamaha; 90hp-40hp with single ram power tilt
systems.
Honda with single ram power tilt systems.
Evinrude and Johnson
with single ram power tilt systems.
Suzuki with single ram power tilt systems,(some Suzuki engines have a plastic housing around the main tilt piston
shaft, we don't recommend using the universal m-ywedge unit on these engines.)
1. Trim outboard to up position.
2. Simply push the universal M-Y Wedge on the power tilt
rod and it will pop or click into place.
3. Trim outboard down until the rubber begins to compress.
4. To remove universal M-Y Wedge simply trim outboard to up
position and remove.
5. Store universal M-Y Wedge in any boat compartment for convenience.
Note; The universal m-ywedge can be cut to
size, if your outboard sits to high or you have problems with tilting your motor high
enough to install the unit. Simply cut the universal m-ywedge using a miter or hack saw,
you normally don't need to cut more than an inch off. |
